Quantcast
Channel: Monday Night Knife Fights Archives | Breach Bang Clear
Viewing all articles
Browse latest Browse all 82

MNKF: MTech “Tactical” Tomahawk

$
0
0

Our tamed Australian breaks things. This time–an Mtech. Mad Duo

Monday Night Knife Fights: MTech “Tactical” Tomahawk
Apocalypse Josh

I have a great fondness for hatchets and tomahawk and quite a collection, ranging from the low-key Fuller camping hatchet to the knockabout United Cutlery M48 to the singular Boker Tomahook. A new addition to my armory was the very blingtastic MTech – Tactical axe.

At 36cm (14 1/4″) overall, this is a decently sized chopper and at 650g (1.4lbs) it’s lighter than I expected. It has a black rubberized ABS handle with lightly textured lanyard loop, and is peppered with seven locking bolts and nuts with Torx fittings. The axehead is 18cm (7 1/8″) with a 9cm (3 1/2″) cutting edge. It has a spike on opposite end, interesting secondary edges, and to top it all off it’s titanium anodized to a gold finish.

One thing that struck me was that ABS, which felt really flimsy. Not that it was flexing under my grip, more that it was light and sounded hollow. The black nylon sheath was simple enough, with a press stud retention loop, and press-stud closures at the rear to keep it in place.

The blade was shipped sharp and had a knife edge, with deep secondary grinds not only along the primary face but also a deep inwardly curved bite in the top of the axehead as well as the underside of the beard. The top of the axe features a set of aggressively cut jimping.

I was hard pressed to think of what that top scalloped edge would be useful for, other than an “upwards” axe thrust. However, scalloping the blade inward rather than having it sweep forward into a point like in a Dane Axe seemed counter productive. Perhaps as a branch trimmer? More likely to make it look extra cool and scary. Gold. Plated. Scary.

The edge at the underside of the beard was alright as a down-sweeping cutting edge although it did come back quite close to the very top handholds, and my delicate pink flesh, when using a choked-up grip. There are cutaways in the bottom of the axehead for thumb and forefinger to rest in, and they were well placed. But again, there was no beveling, and the sharp edges seemed too close and unguarded.

At the back of the axehead is a spike, ground down into a diamond cross-section, and down to quite a significant point. I liked the geometry of it, and it certainly had a fair “bite” when punching holes in logs, chipboard and cans.

Overall, the cutting power of the axe was somewhat limited by its lightweight design. The knife-edge blade was sharp with a thin cross-section, chopped into boards well enough and cut through bike tyre like nobody’s business, but on a meaty target like a log it bit and stuck.

Too light to travel deep enough to cleave, too narrow to form a splitting wedge.

I gave the butt-end a strike to test durability and its utility as an impact weapon, and THIS happened. The ABS plastic, which is what LEGO is made out of, shattered at the shock of impact.

It also exposed the inside of the axe handle, which is something else I wanted to mention. Having felt how light and “hollow” it sounded, I had taken the handle apart with my trusty min/Inch TORX screwdrivers, and popped it open.

It turns out that as well as the thin and hollow framed handle, which I could have lived with and probably filled with resin or replaced with a cord-wrap, the handle itself was made of three separate pieces of different steel. One for the Ti-anodized blingtastic head, a powder coated lanyard loop piece at the butt-end, and a plain piece through the middle.

I’m sure that made the fabrication easier. But I don’t know what kinds of steel are in there, and the welds don’t look all that flash to me. I would have some concerns about wailing too hard on a solid door, wall, or even a tree-trunk with this.

SDI

Perhaps a metallurgist out there can tell me otherwise, but I’m going to relegate this to the back of the collection and save the serious work for serious tools. It seems my MTech Extreme Cleaver was the exception to the rule that these are not hard-use tools.
-AJ

AJ-mtechaxe1



Mad Duo, Breach-Bang& CLEAR!

Comms Plan

Primary: Subscribe to the Breach-Bang-Clear newsletter here; you can also support us on Patreon and find us on Pinterest.

Alternate: Join us on Facebook here or check us out on Instagram here.

Contingency: Exercise your inner perv with us on Tumblr here, follow us on Twitter here or connect on Google + here.

Emergency: Activate firefly, deploy green (or brown) star cluster, get your wank sock out of your ruck and stand by ’til we come get you.
Apocalypse Josh 1 Breach Bang Clear

About the Author: Josh Orth is a second generation expat currently dwelling in the arguably civilized outskirts of Melbourne, Australia. He’s lived in deserts, jungles and urban sprawls around the world and traveled/adventured into assorted inhospitable places around the world and has a keen sense of the speed with which the trappings of ‘civilized Western life’ can disappear. This has led him to begin writing about his interests and observations when it comes to the gear, skills and other necessities of self reliance of being equipped for whatever a capricious, occasionally indurate life might throw at him. This isn’t by any means to say our eccentric friend truly experiences genuine vorfreude about dystopian life, but if he had to he might not complain. Read more by Josh at Apocalypse Equipped.

Grunts: vorfreude.

Breach Bang Clear Apocalypse Josh
madmax-pilot

We’re not saying Josh flies a PL-12 Airtruk. We’re just saying this guy and Josh have never been seen in the same room together at the same time.

The post MNKF: MTech “Tactical” Tomahawk appeared first on Breach Bang Clear.


Viewing all articles
Browse latest Browse all 82

Trending Articles